On Tank
![](https://mfsparts.com/wp-content/uploads/2018/08/1500.jpg)
Remote
![](https://mfsparts.com/wp-content/uploads/2018/08/2500.jpg)
STEP 1: Accessing the Configuration Port
![](https://mfsparts.com/wp-content/uploads/2019/04/C0.png)
Perform configuration prior to installation. With power disconnected, begin by rotating the panel to the bottom side.
![](https://mfsparts.com/wp-content/uploads/2019/04/C1-1.png)
Locate the configuration access port cover. Using a flat head screw driver, carefully loosen one edge of the plastic snap-in cover.
![](https://mfsparts.com/wp-content/uploads/2019/04/C3.png)
Once loose, remove the plastic snap-in cover by hand. Retain the plastic cover, as it should be reinstalled after configuration.
STEP 2: Wiring & Configuration
Verify the configuration based on your existing tank type using the charts below!
DIP SWITCH ON/OFF
- Push to Pump Button Momentary/Timer function
- Enable/Disable Push to Pump Button
- Enable/Disable Call for Pickup Audible Alarm
- Enable/Disable Tank Full Audible Alarm
TURN DIAL (TIMER CONTROL)
DIP 1 must be off for timer. Adjustment from a minimum of 3 minutes (counter clockwise) to a maximum of 30 minutes (clockwise) run time. The timer can be disabled by the operator at any point by pressing the Push to Pump button while the timer is engaged.
![](https://mfsparts.com/wp-content/uploads/2019/06/CONFIG2.png)
Model C - Wiring & Configuration
Applies to: 700111 (1500C), 700115 (2500C), 700450 (OD BOSS)
![](https://mfsparts.com/wp-content/uploads/2019/04/P1.png)
POWER IN
![](https://mfsparts.com/wp-content/uploads/2019/04/P2.png)
HEAT
![](https://mfsparts.com/wp-content/uploads/2019/04/P4.png)
PROBE
![](https://mfsparts.com/wp-content/uploads/2019/04/P5-2.png)
NOT USED
KEEP CAPPED
![](https://mfsparts.com/wp-content/uploads/2019/04/P3-2.png)
NOT USED
KEEP CAPPED
Model H - Wiring & Configuration
Applies to: 700113 (1500H), 700116 (2500H)
![](https://mfsparts.com/wp-content/uploads/2019/04/P1.png)
POWER IN
![](https://mfsparts.com/wp-content/uploads/2019/04/P2.png)
HEAT
![](https://mfsparts.com/wp-content/uploads/2019/04/P4.png)
PROBE
![](https://mfsparts.com/wp-content/uploads/2019/04/P5-2.png)
NOT USED
KEEP CAPPED
![](https://mfsparts.com/wp-content/uploads/2019/04/P3.png)
BALL VALVE
Model CH - Wiring & Configuration
Applies to: 700183 (1500CH), 700184 (2500CH)
![](https://mfsparts.com/wp-content/uploads/2019/04/P1.png)
POWER IN
![](https://mfsparts.com/wp-content/uploads/2019/04/P2.png)
HEAT
![](https://mfsparts.com/wp-content/uploads/2019/04/P4.png)
PROBE
![](https://mfsparts.com/wp-content/uploads/2019/04/P5.png)
MOTOR
![](https://mfsparts.com/wp-content/uploads/2019/04/P3.png)
BALL VALVE
Model D - Wiring & Configuration
Applies to: 700112 (1500D), 700115 (2500D)
![](https://mfsparts.com/wp-content/uploads/2019/04/P1.png)
POWER IN
![](https://mfsparts.com/wp-content/uploads/2019/04/P2.png)
HEAT
![](https://mfsparts.com/wp-content/uploads/2019/04/P4.png)
PROBE
![](https://mfsparts.com/wp-content/uploads/2019/04/P5.png)
MOTOR
![](https://mfsparts.com/wp-content/uploads/2019/04/P3-2.png)
NOT USED
KEEP CAPPED